"Classic 120" 3D Printed Concrete Fence
3D printed concrete fence with the widest columns in the range — 117 cm. The most monumental look.
Price per m² of a "column + 2300 mm panel" section. With shorter panels the price per m² is higher.
Discuss your order Message on Viber
| Column spacing (centre to centre) | 0.4–3.2 m |
| Flat panel length | 0.8–2.3 m, in 100 mm increments |
| Panel insertion into column | 15 cm at each end |
| Foundation | pad (pier) foundation |
| Warranty | 20 years |
"Classic 120" is the choice when a fence should look like a monumental stone wall. Wide columns alternate with flat panels, and the horizontal texture of the print layers keeps the result powerful without feeling heavy.
How it works
A column (with one groove, two grooves or none) and a flat panel up to 2.3 m long. Shorter panels are made in 100 mm increments down to 0.8 m. The central cavity of the wide column does not have to be filled with concrete; it can be closed with a 3D BETON concrete cap instead.
Tongue-and-groove joint
The panel slots 15 cm into the column at each end, and the joint is filled with concrete. The joints take up 30 cm of panel length. 90° corners and any other angles are formed with a single-groove or ungrooved column.
Who it is for
Houses with strong architecture, cottages, entrance features and sites where the fence must withstand high wind loads.
Frequently asked questions
What concrete do you print with?
Heavyweight concrete made with clean cubical crushed stone up to 10 mm, with no dusty screenings. The sand is quarry sand; clay and metal particles are removed by a powerful magnet above the conveyor. For thin-walled products we use only fresh M500 cement, which does not cause efflorescence, plus a plasticiser. Because the layers are compacted by extrusion rather than vibration, the mix contains more cement than ordinary concrete.
Why is every element 20 cm high?
Our production is standardised around this height. Almost any structure can be broken down into blocks in multiples of 20 cm with monolithic joints. This height gives precise layer geometry without the "elephant foot" effect and a manageable block weight: 40 kg on average, about 60 kg at most, so two people can lift it.
Will 3D printed concrete crack?
Every structure includes monolithic joints that carry the dead load, wind and snow, as well as expansion joints, composite reinforcement and coarse aggregate that acts as micro-reinforcement. As a result, the products withstand transport over 1,500+ km and all service loads. The design service life is over 100 years.
How are the products reinforced?
Each printed contour is reinforced twice along its height with certified composite rebar from a trusted manufacturer (Arvit). It does not lose its properties over time.
How do you ensure the layers bond into a solid whole?
Layer-to-layer adhesion is the key to 3D printing. We control the layer deposition time, concrete workability, air humidity and temperature, and the products are cured in a steam chamber.
Does a fence need a strip foundation?
No. Most fences are installed on point pier foundations with vertical rebar starters (usually 2 bars of 12 mm diameter). The entire load of a section is transferred to the monolithic joints, so a strip foundation is unnecessary, and a pier foundation cuts the amount of reinforcement and concrete work by about 5 times. Houses, of course, need a strip foundation or an insulated slab foundation.
I already have a strip foundation with posts. Will it work?
Send us the measurements and post spacing, and we will design a matching structure. If they don't match, the old posts or rebar are cut off and new anchors are set with chemical anchoring, or rebar is driven into the existing foundation.
My dog digs under the fence. What can I do?
Rather than building a strip foundation, it is more cost-effective to bury the bottom 1–2 rows of the fence. W6 concrete performs well in the ground.
Let's discuss your project
Leave your phone number and we'll call you back within one business day. Or message us on Viber.
Or call us:
+38 067 401 00 94