VisualizationModular 3D Printed Concrete Bench
Modular 3D printed concrete bench of the length you need: straight, wavy, circular or made to your drawings.
Price per linear m.
Thermo-ash finish: +UAH 3,350 / linear m, UAH 8,350 / linear m in total
Made to orderDiscuss your order ↗ Message on Viber
Idea: a place to unwind in your yard →
| Price | UAH 5,000 per linear metre |
| Thermo-ash finish | +UAH 3,350 per linear metre |
| Shape | straight, wavy, circular or to your drawing |
| Design | modular |
| Warranty | 20 years |
The bench is assembled from separate concrete modules, so its length and shape are chosen to suit the site: a straight line along a path, a wave between flower beds, a ring on a square or in a courtyard. Benches like this are used in parks, residential courtyards, squares, near schools and offices, and in private gardens.
Price per linear metre
The modular bench costs UAH 5,000 per linear metre, so the price depends on its length. For example, a 4 m bench costs UAH 20,000, or UAH 33,400 with a thermo-ash finish.
Thermo-ash finish
The seat of the concrete bench can be finished with thermo-ash: an option for the bench at UAH 3,350 per linear metre. Thermo-ash is ash wood treated at high temperature. It absorbs less moisture than ordinary wood, so it copes better outdoors, and a wooden seat feels warmer than concrete.
Options
- thermo-ash seat finish: +UAH 3,350 per linear metre
- built-in lighting: priced separately
How to order
Send us a plan or drawing, or describe where the bench will stand and how long it should be. The bench can be made to your own drawings. We will calculate the price, print the modules and deliver them across Ukraine; installation is carried out by our partners.
Frequently asked questions
What concrete do you print with?
Heavyweight concrete made with clean cubical crushed stone up to 10 mm, with no dusty screenings. The sand is quarry sand; clay and metal particles are removed by a powerful magnet above the conveyor. For thin-walled products we use only fresh M500 cement, which does not cause efflorescence, plus a plasticiser. Because the layers are compacted by extrusion rather than vibration, the mix contains more cement than ordinary concrete.
Why is every element 20 cm high?
Our production is standardised around this height. Almost any structure can be broken down into blocks in multiples of 20 cm with monolithic joints. This height gives precise layer geometry without the "elephant foot" effect and a manageable block weight: 40 kg on average, about 60 kg at most, so two people can lift it.
Will 3D printed concrete crack?
Every structure includes monolithic joints that carry the dead load, wind and snow, as well as expansion joints, composite reinforcement and coarse aggregate that acts as micro-reinforcement. As a result, the products withstand transport over 1,500+ km and all service loads. The design service life is over 100 years.
How are the products reinforced?
Each printed contour is reinforced twice along its height with certified composite rebar from a trusted manufacturer (Arvit). It does not lose its properties over time.
How do you ensure the layers bond into a solid whole?
Layer-to-layer adhesion is the key to 3D printing. We control the layer deposition time, concrete workability, air humidity and temperature, and the products are cured in a steam chamber.
What equipment do you print on?
On industrial CRAFTRUDER construction 3D printing equipment.
Does a fence need a strip foundation?
No. Most fences are installed on point pier foundations with vertical rebar starters (usually 2 bars of 12 mm diameter). The entire load of a section is transferred to the monolithic joints, so a strip foundation is unnecessary, and a pier foundation cuts the amount of reinforcement and concrete work by about 5 times. Houses, of course, need a strip foundation or an insulated slab foundation.
I already have a strip foundation with posts. Will it work?
Send us the measurements and post spacing, and we will design a matching structure. If they don't match, the old posts or rebar are cut off and new anchors are set with chemical anchoring, or rebar is driven into the existing foundation.
Tell us about your project
Send a sketch, drawing or photo of your site. We'll pick the product, work out the price, agree on quantity and delivery, and our partners will handle installation.
- Phone and Viber+38 067 401 00 94
- E-mailinfo@3dbeton.com.ua
- ViberMessage on Viber
Files, drawings and photos are easiest to send via Viber or e-mail.